
8 041
T:TX Jobs/LS
*CTL
These SPs count the applications that stored files on
the document server that were later accessed for
transmission over the telephone line or over a
network (attached to an e-mail, or as a fax image by
I-Fax).
[0 to 9999999/ 0 / 1]
Note: Jobs merged for sending are counted
separately.
The L: counter counts the number of jobs scanned
from within the document server mode screen at the
operation panel.
8 042
C:TX Jobs/LS
*CTL
8 043
F:TX Jobs/LS
*CTL
8 044
P:TX Jobs/LS
*CTL
8 045
S:TX Jobs/LS
*CTL
8 046
L:TX Jobs/LS
*CTL
8 047
O:TX Jobs/LS
*CTL
• When a stored copy job is sent from the document server, the C: counter increments.
• When images stored on the document server by a network application or Palm2 are sent as an e-
mail, the O: counter increments.
8 051
T:TX Jobs/DesApl
*CTL
These SPs count the applications used to send files
from the document server over the telephone line or
over a network (attached to an e-mail, or as a fax
image by I-Fax). Jobs merged for sending are
counted separately.
[0 to 9999999/ 0 / 1]
The L: counter counts the number of jobs sent from
within the document server mode screen at the
operation panel.
8 052
C:TX Jobs/DesApl
*CTL
8 053
F:TX Jobs/DesApl
*CTL
8 054
P:TX Jobs/DesApl
*CTL
8 055
S:TX Jobs/DesApl
*CTL
8 056
L:TX Jobs/DesApl
*CTL
8 057
O:TX Jobs/DesApl
*CTL
• If the send is started from Desk Top Binder or Web Image Monitor, for example, then the O:
counter increments.
8 061
T:FIN Jobs
*CTL
[0 to 9999999/ 0 / 1]
These SPs total the finishing methods. The finishing method is specified by the
application.
8 062
C:FIN Jobs
*CTL
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for copy jobs only. The finishing method is specified
by the application.
5. System Maintenance
672
Summary of Contents for AP-C3
