manualshive.com logo in svg

Realtek Ameba-D RTL872 D Series, User Manual

The Realtek Ameba-D RTL872 D Series features cutting-edge technology for high-performance IoT devices. Unlock the full potential of your device with the comprehensive User Manual, available for free download at our website. Find everything you need to get started and maximize your experience with this advanced product.

Share
Download
background image

                                                                                                      

                             Ameba-D User Manual 

User Manual                                                                                                                       All information provided in this document is subject to legal disclaimers.                                                            © REALTEK 2019. All rights reserved.

 

220 

25 

OC0PE 

R/W 

0 

Output Compare 0 preload enable 

 

0: Preload register on CCR0 is disabled. CCR0 can be written at any time, the new 
value is taken in account immediately. 

 

1: Preload register on CCR0 is enabled. Read/write operations access the preload 
register. CCR0 preload value is loaded in the active register at each update event. 

24 

CC0E 

R/W 

0 

CC0 enable 

 

0: CC0 is disabled. 

 

1: CC0 is enabled. 

23:16 

RSVD 

N/A 

- 

Reserved 

15:0 

CCR0 

R/W 

0 

Capture/compare 0 value 

 

If channel CC0 is configured as output: CCR0 is the value to be loaded in the actual 
capture/compare 0 register (preload value). It is loaded permanently if the preload 
feature isn’t selected in the OC0PE bit. Else the preload value is copied in the active 
capture/compare 0 register when an update event occurs. 
The active capture/compare register contains the value to be compared to the 
counter TIMx_CNT and signaled on OC0 output. 

 

If channel CC0 is configured as input: CCR0 is the counter value transferred by the 
last input capture event (TRGI). 

Note

: Value must be 0 ~ 100 (including 0 & 100). 

10.4.3.10

 

TIMx Capture/Compare Register 1 (TIMx_CCR1) 

 

Name:

 TIM5 capture/compare register 1 

 

Address offset: 

0x24

 

 

Reset value: 

0x00000000

 

 

Read/write access:

 read/write 

 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

RSVD 

CC1M 

CC1P 

OC1PE 

CC1E 

RSVD 

R/W 

R/W 

R/W 

R/W 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

CCR1 

R/W 

 

Bit 

Name 

Access  Reset 

Description 

31:28 

RSVD 

N/A 

- 

Reserved 

27 

CC1M 

R/W 

0 

Refer to CC0M description in TIMx_CCR0 

26 

CC1P 

R/W 

0 

Refer to CC0P description in TIMx_CCR0 

25 

OC1PE 

R/W 

0 

Refer to OC0PE description in TIMx_CCR0 

24 

CC1E 

R/W 

0 

Refer to CC0E description in TIMx_CCR0 

23:16 

RSVD 

N/A 

- 

Reserved 

15:0 

CCR1 

R/W 

0 

Refer to CCR0 description in TIMx_CCR0 

10.4.3.11

 

TIMx Capture/Compare Register 2 (TIMx_CCR2) 

 

Name:

 TIM5 capture/compare register 2 

 

Address offset: 

0x28

 

 

Reset value: 

0x00000000

 

 

Read/write access:

 read/write 

 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

RSVD 

CC2M 

CC2P 

OC2PE 

CC2E 

RSVD 

R/W 

R/W 

R/W 

R/W 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

CCR2 

R/W 

Realtek confidential files

The document authorized to

SZ99iot

2019-05-15 10:08:03

Summary of Contents for Ameba-D RTL872 D Series















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ameba-D RTL872 D Series

Yamaha 100A Service Manual preview
100A
Brand: Yamaha Pages: 20
Quick BTR185 User Manual preview
BTR185
Brand: Quick Pages: 44
Quectel LC76G Series User Manual preview
LC76G Series
Brand: Quectel Pages: 34
Ampro CoreModule 420 Reference Manual preview
CoreModule 420
Brand: Ampro Pages: 72
Infineon UltraHub User Manual preview
UltraHub
Brand: Infineon Pages: 24
Renesas R0K5R8C34DK2HBR Hardware Instruction Manual preview
R0K5R8C34DK2HBR
Brand: Renesas Pages: 32
ST STM32479I-EVAL User Manual preview
STM32479I-EVAL
Brand: ST Pages: 77
Aaeon SBC-455 Product Manual preview
SBC-455
Brand: Aaeon Pages: 97
QDI P4I865 PEA User Manual preview
P4I865 PEA
Brand: QDI Pages: 85
DTK PAM-0052V User Manual preview
PAM-0052V
Brand: DTK Pages: 50
Renesas ISL81802EVAL3Z User Manual preview
ISL81802EVAL3Z
Brand: Renesas Pages: 20
DFI EHL171 Quick Reference preview
EHL171
Brand: DFI Pages: 5
Gigabyte GA-MA74GMT-S2 User Manual preview
GA-MA74GMT-S2
Brand: Gigabyte Pages: 100
M-system DiskOnChip PCI-G-EVB User Manual preview
DiskOnChip PCI-G-EVB
Brand: M-system Pages: 14
FIC FR33E Manual preview
FR33E
Brand: FIC Pages: 52
TYAN TITAN TURBO PLUS ATX Manual preview
TITAN TURBO PLUS ATX
Brand: TYAN Pages: 69
JETWAY S450R2A User Manual preview
S450R2A
Brand: JETWAY Pages: 48
JETWAY HBJC390F841VAG34B Technical Manual preview
HBJC390F841VAG34B
Brand: JETWAY Pages: 44

Brands by name

Popular brands

Load more brands