Oracle Sun Netra X4270 Service Manual Download Page 216

Page: 216 / 238

Network Management Port

TABLE 8

Gigabit Ethernet Port Signals

Pin

Signal Description

Pin

Signal Description

Transmit/Receive Data 0 +

Transmit/Receive Data 2 –

Transmit/Receive Data 0 –

Transmit/Receive Data 1 –

Transmit/Receive Data 1 +

Transmit/Receive Data 3 +

Transmit/Receive Data 2 +

Transmit/Receive Data 3 –

Related Information

■

“Rear Panel Cable Connections” on page 17

■

“Ethernet Port LEDs” on page 24

■

“Disconnect Cables From the Server” on page 80

■

“Reconnect Power and Data Cables” on page 213

Network Management Port

The server has one 10BASE-T Ethernet management domain interface, labeled NET MGT. For

information on configuring this port for managing the server with ILOM, refer to the ILOM 3.0

documentation.

216

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands