Oracle Sun Netra X4270 Service Manual Download Page 184

Page: 184 / 238

Replacing Power Supplies

Replacing Power Supplies

The server???s redundant power supplies support concurrent maintenance, which enables you

to remove and replace a power supply without shutting the server down, provided that the other

power supply is online and working.

The following LEDs are lit when a power supply fault is detected:

■

Front and rear Service Required LEDs

■

Amber Fault LED on the faulty power supply

If a power supply fails and you do not have a replacement available, leave the failed power

supply installed to ensure proper air flow in the server.

Caution -

Safety agency requirements prohibit changing a system from AC input to DC input

or from DC input to AC input after the product has been removed from the agency approved

manufacturing site.

■

“Remove a Power Supply” on page 184

■

“Install a Power Supply” on page 187

Related Information

■

“Replacing the Power Distribution Board” on page 203

Remove a Power Supply

Identify which power supply requires replacement.

184

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands