Oracle Sun Netra X4270 Service Manual Download Page 229

Page: 229 / 238

VT-d

SATA

serial advanced technology attachment.

SCSI

small computer system interface.

SER MGT

serial management port. The default port for system management, especially during the initial

system configuration.

SFF

small form factor.

service processor.

SR DIMM

single-rank DIMM.

SSH

secure shell.

STP

shielded twisted pair.

TCG

Trusted Computing Group.

TPM

trusted platform module. For more information, refer to the Microsoft Windows Trusted

Platform Module Management documentation.

US NEC

United States National Electrical Code. A United States standard for the installation of

electrical wiring and equipment.

USB

universal serial bus.

VAC

volts of alternating current.

VDC

volts of direct (continuous) current.

VGA

video graphics array.

VT-d

virtualization technology for directed I/O.

Glossary

229

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands