Oracle Sun Netra X4270 Service Manual Download Page 102

Page: 102 / 238

Remove the PCI Mezzanine

■

CPU modules

■

Flash modules and Flash module cable

■

ESM riser and ESM

■

Battery

It is not necessary to remove the PCI mezzanine for other components. However, when you

remove the PCI mezzanine, you make additional working space available.

■

“Remove the PCI Mezzanine” on page 102

■

“Install the PCI Mezzanine” on page 104

Related Information

■

“Replacing PCIe2 Cards” on page 112

Remove the PCI Mezzanine

Note -

PCIe2 cards installed in slots 4 and 5, as well as the installed SAS controller HBA, can

remain in place when removing the PCI Mezzanine.

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Disconnect all I/O cables from the rear of the PCI mezzanine.

These cables should have been removed prior to removing the server from the rack. These

cables include the external SAS cable, alarm cable, and any I/O cables connected to installed

PCIe cards.

Disconnect the following PCI mezzanine cables:

■

LED board cable

■

Fan tray 1 power cable

■

Power cable from PDB

■

Internal SAS HBA cable

■

Fan tray 2 power cable

102

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands