Oracle Sun Netra X4270 Service Manual Download Page 29

Page: 29 / 238

Inspecting the Server

These topics introduce the diagnostic tools and strategies available to help you diagnose

problems with the system.

■

“Diagnostic Tools” on page 29

■

“Service Troubleshooting Task List” on page 30

■

“Gather Service Information” on page 31

■

“Inspecting the System” on page 32

Related Information

■

“Understanding the Server” on page 13

■

“Preparing for Service” on page 73

■

“Returning Server to Operation” on page 211

Diagnostic Tools

There are a variety of diagnostic tools, commands, and indicators you can use to monitor and

troubleshoot the server:

■

LEDs

– These indicators provide a quick visual notification of the status of the server and

of some of the FRUs.

■

ILOM firmware

– This system firmware runs on the service processor. In addition to

providing the interface between the hardware and OS, ILOM also tracks and reports the

health of key server components. ILOM works closely with POST and Oracle Solaris

Predictive Self-Healing technology to keep the system up and running even when there is a

faulty component.

■

PC-Check

– Accessed through ILOM, the DOS-based PC-Check utility tests all

motherboard components (CPU, memory, and I/O), ports, and slots. If enabled through

ILOM, this utility will run each time the system powers on. For information about the PC-

Check, refer to the

Sun x64 Servers Diagnostics Guide

Inspecting the Server

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands