Oracle Sun Netra X4270 Service Manual Download Page 228

Page: 228 / 238

OSP

OSP

outside plant.

PCIe2

peripheral component interconnect express 2.0. Refers to cards or slots that support the PCI

Express 2.0 specification.

PDB

power distribution board.

POST

power-on self-test.

PSH

predictive self-healing.

PSU

power supply unit.

PXE

preboot execution environment.

QR DIMM

quad-rank DIMM.

RAID

redundant array of independent disks.

RAS

Reliability, Availability, and Serviceability.

RIS

remote installation services.

RPM

rotations per minute.

RTS

request to send.

S.M.A.R.T.

self-monitoring, analysis, and reporting technology.

SAS

serial attached SCSI.

228

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands