Oracle Sun Netra X4270 Service Manual Download Page 107

Page: 107 / 238

Replacing PCIe2 Risers

Return the server to operation.

See

“Returning Server to Operation” on page 211

Related Information

■

“Remove the PCI Mezzanine” on page 102

■

“Replacing PCIe2 Risers” on page 107

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

Replacing PCIe2 Risers

PCIe2 cards in slots 0, 1, and 2 are installed on vertical risers. You must remove the relevant

riser to remove and replace a PCIe2 card. You must remove all three PCIe risers when replacing

the motherboard.

Description

Links

Locate the three PCIe2 risers and understand their

differences.

“PCIe2 Riser Location and Differences” on page 107

Remove a PCIe2 riser from the motherboard assembly.

“Remove a PCIe2 Riser” on page 108

Install a PCIe2 riser to the motherboard assembly.

“Install a PCIe2 Riser” on page 110

Related Information

■

“Replacing the PCI Mezzanine” on page 101

■

“Replacing PCIe2 Cards” on page 112

PCIe2 Riser Location and Differences

The motherboard connector for PCIe2 riser 0 is different than the connector used by PCIe2

risers 1 and 2. Do not attempt to install a PCIe2 riser in a different location on the motherboard.

Replacing Motherboard Assembly Components

107

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands