Oracle Sun Netra X4270 Service Manual Download Page 13

Page: 13 / 238

Understanding the Server

These topics describe the controls, connectors, LEDs, system components, and replaceable

components of the server.

■

“Locating Controls and Connectors” on page 13

■

“Locating Server and Component LEDs” on page 18

■

“System Components” on page 25

■

“Field-Replaceable Units” on page 27

Related Information

■

“Inspecting the Server” on page 29

■

“Identifying the Server Ports” on page 215

Locating Controls and Connectors

The following topics describe the controls and connectors located on the front and rear panels.

■

“Front Panel Controls On Two-Drive System” on page 14

■

“Front Panel Components on Two-Drive Systems With Bezel Removed” on page 15

■

“Front Panel Components on Four-Drive Systems With Bezel Removed” on page 16

■

“Rear Panel Cable Connections” on page 17

Related Information

■

“Locating Server and Component LEDs” on page 18

■

“System Components” on page 25

■

“Field-Replaceable Units” on page 27

Understanding the Server

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands