manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 14

Locating Controls and Connectors

Front Panel Controls On Two-Drive System

Note - 

Systems with two drives will contain a DVD drive that you can control through the front

bezel. Four drive systems will be not contain a DVD drive.

No.

Description

Additional Information

1

User alarm status LEDs

Top to bottom – Critical LED, Major LED, Minor LED, User LED

2

System status LEDs

Left to right – Locator LED button, Service Required LED, System

Activity LED, Power button

3

Removable media

Only in two drive configurations

Related Information

■

“Front Panel Components on Two-Drive Systems With Bezel Removed” on page 15

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

14

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands