manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 145

Remove a Flash Module

When a flash module is faulty, an amber LED on the flash module will light when you press the

Fault Remind button.

Note - 

Whenever the Fault Remind button is presses, a LED located next to the Fault Remind

button lights green to indicate that there is sufficient voltage present to light any fault LEDs on

the motherboard assembly. If this Fault Remind LED fails to light when you press the button,

the capacitor power the fault remind circuit might have lost its charge. The capacitor can lose its

charged if the Fault Remind button is pressed for a long time or if the power cables have been

removed for more than 15 minutes.

5.

Verify that the flash module power LED on the motherboard assembly is off.

Caution - 

Removing a flash module when the flash module power LED is lit will damage the

flash module.

Replacing Motherboard Assembly Components

145

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands