manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 93

Replacing the Media Bay Assembly

■

If you installed the optical media drive as part of another procedure, return to that

procedure.

■

Otherwise, perform the following tasks to bring the server back online:

■

“Close Front Bezel” on page 85

■

“Remove Antistatic Measures” on page 212

Related Information

■

“Remove the Optical Media Drive” on page 91

Replacing the Media Bay Assembly

These tasks describe how to remove and replace the media bay assembly.

Note - 

Because of EMI compliance requirements, field upgrades between four drive system

configurations to two drive and optical media drive configurations are not supported.

■

“Remove the Media Bay Assembly” on page 93

■

“Install the Media Bay Assembly” on page 97

Related Information

■

“Replacing a Drive” on page 85

■

“Replacing the Optical Media Drive” on page 91

Remove the Media Bay Assembly

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

Remove the air duct.

See 

“Remove the Air Duct” on page 127

3.

Remove all the drives from the system.

Make a note of the locations of each drives.

Replacing Storage Components

93

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands