Oracle Sun Netra X4270 Service Manual Download Page 127

Page: 127 / 238

Replacing the Air Duct

See

“Install the PCI Mezzanine” on page 104

11.

Return the server to operation.

See

“Returning Server to Operation” on page 211

12.

Connect any external cable to the PCIe2 card.

Refer to your PCIe2 card documentation for more information.

Related Information

■

“Replacing PCIe2 Risers” on page 107

■

“PCIe2 Riser Location and Differences” on page 107

■

“Remove the Lower PCIe2 Cards” on page 123

Replacing the Air Duct

You must remove the air duct to access certain motherboard components like the DIMMs and

CPUs.

■

“Remove the Air Duct” on page 127

■

“Install the Air Duct” on page 130

Related Information

■

“Replacing DIMMs” on page 132

■

“Replacing CPUs” on page 160

Remove the Air Duct

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Replacing Motherboard Assembly Components

127

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands