Oracle Sun Netra X4270 Service Manual Download Page 89

Page: 89 / 238

Install a Drive

Caution -

The latch is not an ejector. Do not bend the latch too far to the left. Doing so can

damage the latch.

Grasp the latch and pull the drive out of the drive slot.

Consider your next steps:

■

If you are replacing the drive, continue to

“Install a Drive” on page 89

■

If you are not replacing the drive, perform administrative tasks to configure the server to

operate without the drive.

Related Information

■

“Drive LEDs” on page 21

■

“Drives Hot-Plug Conditions” on page 85

■

“Install a Drive” on page 89

Install a Drive

Remove the replacement drive from its packaging and place the drive on an

antistatic mat.

Replacing Storage Components

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands