manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 182

Install the Air Filter

Related Information

■

“Front Panel Components on Two-Drive Systems With Bezel Removed” on page 15

■

“Front Panel Components on Four-Drive Systems With Bezel Removed” on page 16

■

“Opening and Closing the Front Bezel” on page 83

■

“Install the Air Filter” on page 182

Install the Air Filter

1.

Consider your first steps:

■

If you are replacing an air filter, remove the faulty air filter first, then return to

Step 2 of this procedure.

■

If you are installing the filter tray as part of another component’s removal or

installation procedure, go to Step 4.

2.

Remove the replacement air filter from its packaging.

3.

Feed the edges of the air filter under the restraining hooks of the filter tray.

4.

Massage the filter in the filter tray so that there are no folds or wrinkles, and so

that the air filter lies flat against the filter tray.

5.

Press the air filter into the bezel until it snaps into place.

182

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands