Oracle Sun Netra X4270 Service Manual Download Page 192

Page: 192 / 238

Replacing Fan Tray 2

Reconnect the fan tray 0 power cable to the PCI mezzanine.

Route the fan tray cable back into the air duct???s cable guides.

Consider your next step:

■

If you installed the fan assembly as part of another procedure, return to that procedure.

■

Otherwise, return the server to operation.
See

“Returning Server to Operation” on page 211

Related Information

■

“Replacing the Air Duct” on page 127

■

“Remove Fan Tray 0” on page 189

Replacing Fan Tray 2

Fan tray 2 (labeled FT2) is located under the media bay assembly, next to fan tray 0.

■

“Remove Fan Tray 2” on page 193

■

“Install Fan Tray 2” on page 194

192

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands