manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 194

Install Fan Tray 2

4.

Set fan tray 2 aside on an antistatic mat.

5.

Consider your next step:

■

If you removed the fan assembly as part of another procedure, return to that procedure.

■

Otherwise, continue to 

“Install Fan Tray 2” on page 194

.

Related Information

■

“Replacing the Media Bay Assembly” on page 93

■

“Replacing Fan Tray 0” on page 189

■

“Install Fan Tray 2” on page 194

■

“Replacing the Power Distribution Board” on page 203

Install Fan Tray 2

1.

Remove the replacement fan tray 2 from its packaging and place it on an

antistatic mat.

2.

Insert the replacement fan tray 2 in the slot with the airflow direction arrow

facing the rear of server.

194

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands