manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 203

Replacing the Power Distribution Board

8.

Return the server to operation.

See 

“Returning Server to Operation” on page 211

.

Related Information

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

■

“Remove the LED Board” on page 199

Replacing the Power Distribution Board

Follow these tasks to remove and install the power distribution board.

■

“Remove the Power Distribution Board” on page 203

■

“Install the Power Distribution Board” on page 206

Related Information

■

“Replacing the Motherboard Assembly” on page 168

■

“Replacing Power Supplies” on page 184

Remove the Power Distribution Board

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

Remove the following components to expose the power distribution board:

■

“Remove a Power Supply” on page 184

■

“Remove the Optical Media Drive” on page 91

■

“Remove a Drive” on page 86

■

“Remove Fan Tray 0” on page 189

■

“Remove Fan Tray 2” on page 193

■

“Remove the Media Bay Assembly” on page 93

Replacing Chassis Components

203

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands