manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 92

Install the Optical Media Drive

4.

Consider your next step:

■

If you removed the optical media drive as part of another procedure, return to that

procedure.

■

Otherwise, continue to 

“Install the Optical Media Drive” on page 92

.

Related Information

■

“Install the Optical Media Drive” on page 92

Install the Optical Media Drive

1.

Remove the replacement optical media drive from its packaging and place it on

an antistatic mat.

2.

Hold the tab to the left and insert the optical media drive into the media bay

assembly.

3.

Press the optical media drive in until it seats and release the tab.

4.

Close the bezel.

5.

Consider your next step:

92

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands