manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 15

Locating Controls and Connectors

Front Panel Components on Two-Drive Systems

With Bezel Removed

No.

Description

Additional Information

1

User alarm LEDs

Top to bottom – Critical LED, Major LED, Minor LED, User LED

Note - 

Also displayed through the front bezel

2

System status LEDs

Left to right – Locator LED button, Service Required LED, System Activity LED, Power button

Note - 

Also displayed through the front bezel

3

Optical media drive

Labeled DVD

4

Drive 1

Labeled 1

5

Drive 0

Labeled 0

6

Drive LEDs

Top to bottom – OK to Remove LED, Service Required LED, Power OK LED

Related Information

■

“Front Panel Controls On Two-Drive System” on page 14

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

■

“Drive LEDs” on page 21

Understanding the Server

15

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands