Oracle Sun Netra X4270 Service Manual Download Page 187

Page: 187 / 238

Install a Power Supply

Related Information

■

“Rear Panel Cable Connections” on page 17

■

“Power Supply LEDs” on page 23

■

“Install a Power Supply” on page 187

Install a Power Supply

Caution -

Never

mix AC and DC power supplies in the same system. Catastrophic system

damage will occur. Always replace the failed power supply with the same type of power supply.

Caution -

Safety agency requirements prohibit changing a system from AC power supplies to

DC power supplies or from DC power supplies to AC power supplies after the product has been

removed from the agency approved manufacturing site.

Remove the replacement power supply from its packaging and place it on an

antistatic mat.

Align the replacement power supply with the empty power supply bay.

Slide the power supply into the bay until it is fully seated.

Replacing Chassis Components

187

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands