Oracle Sun Netra X4270 Service Manual Download Page 164

Page: 164 / 238

Install a CPU

Ensure that the orientation is correct as damage might result if the CPU pins are not aligned

correctly.

Lower the pressure frame.

Ensure that the pressure frame sits flat around the periphery of the CPU.

Engage the release lever by rotating it downward and slipping it under the catch

[2].

Use the syringe (supplied with the new or replacement CPU) to apply

approximately 0.1 ml of thermal grease to the center of the top of the CPU.

Do not distribute the grease, as the CPU heatsink pressure will do so for you.

Inspect the heatsink for dust and lint.

Clean heatsink if necessary.

164

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands