Oracle Sun Netra X4270 Service Manual Download Page 44

Page: 44 / 238

BIOS Setup Utility Menus

Menu

Description

Advanced

Configuration information for the CPU, memory, IDE, Super IO, trusted computing, USB,

PCI, MPS and other information.

PCI

Configure the server to clear NVRAM during system boot.

Boot

Configure the boot device priority (storage drives and the DVD-ROM drive).

Security

Set or change the user and supervisor passwords.

Chipset

View the configuration of server chipsets.

Exit

Save changes and exit, discard changes and exit, discard changes, or load optimal or fail-safe

defaults.

See

“Understanding BIOS Setup Screens” on page 62

for examples of each of these

screens.

To navigate the menus or options listed on a menu, use the arrow keys. The options or fields

that you can configure on a menu appear in color. For further instructions on how to navigate

and change settings in the BIOS Setup utility, refer to the online instructions provided on the

menu.

The following figure identifies the sub-menus that you can access from each of the seven top-

level BIOS menus.

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands