manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 185

Remove a Power Supply

FIGURE   17

Power Supplies and Latches

Figure Legend

1

Power Supply 0

2

Power Supply 1

A lighted amber LED on a power supply indicates that a failure was detected. You can also use

the ILOM 

show

 

faulty

 command at the 

sc>

 prompt.

Note - 

The fans of a failed power supply may still be spinning when the system is powered on.

The failed power supply is still okay to remove.

2.

Log in to the ILOM service processor as root.

Refer to the ILOM 3.0 documentation for instructions.

3.

At the ILOM prompt (

->

), type the 

stop /SYS/PS

n

 command.

The 

stop

 command indicates if it is okay to perform a hot removal of a power supply. This

command does not perform any action, but it provides a warning if the power supply should not

be removed because the other power supply is not providing power to the server.

Replacing Chassis Components

185

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands