manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 83

Replacing Storage Components

These topics provide instructions for replacing the following storage components.

■

“Opening and Closing the Front Bezel” on page 83

■

“Replacing a Drive” on page 85

■

“Replacing the Optical Media Drive” on page 91

■

“Replacing the Media Bay Assembly” on page 93

Related Information

■

“Replacing Motherboard Assembly Components” on page 101

■

“Replacing Chassis Components” on page 179

Opening and Closing the Front Bezel

When replacing components like drives and the air filter from the front of the system, you will

be required to open the front bezel.

■

“Open Front Bezel” on page 84

■

“Close Front Bezel” on page 85

Related Information

■

“Replacing a Drive” on page 85

■

“Replacing the Optical Media Drive” on page 91

Replacing Storage Components

83

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands