manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 98

Install the Media Bay Assembly

FIGURE   9

Connecting the Media Bay Assembly Cables

Figure Legend

1

SATA cable from motherboard (connected on optical media drive-equipped servers only)

2

Power/signal cable from the PDB

3

SAS cable from the SAS HBA

6.

Install the optical media drive and the drives into the same slots that you

removed them.

■

“Install the Optical Media Drive” on page 92

■

“Install a Drive” on page 89

■

“Close Front Bezel” on page 85

7.

Consider your next step:

■

If you installed the media bay bracket as part of another procedure, return to that procedure.

■

Otherwise, continue to the next step.

8.

Install the air duct.

98

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands