manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 111

Install a PCIe2 Riser

2.

Retrieve the PCIe2 riser and gently press the riser into the motherboard

connector until it seats.

3.

Use a No. 2 Phillips screwdriver to tighten the three green captive screws

securing the PCIe riser to the system.

One internal captive screw secures the riser to the motherboard, and two external screws secure

the riser to rear panel.

4.

If there is a PCIe2 card installed in the riser, reconnect any external or internal

cables to the card.

5.

Return the server to operation.

See 

“Returning Server to Operation” on page 211

.

Related Information

■

“PCIe2 Riser Location and Differences” on page 107

■

“Remove a PCIe2 Riser” on page 108

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

Replacing Motherboard Assembly Components

111

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands