manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 77

Power Down Server Gracefully Using the Power Button

Refer to the ILOM 3.0 documentation for instructions.

5.

At the ILOM prompt, shut down the operating system:

-> 

stop /SYS

SC Alert: SC Request to Power Off Host.

If the system is running the Solaris OS, refer to the Solaris system administration

documentation for additional information.

6.

Shut down the chassis power:

-> 

stop /SP

SP Alert: SP Request to Power Off Chassis.

Refer to the ILOM 3.0 documentation for more information about the 

stop

 command.

Note - 

You can also use the Power button on the front of the server to initiate a graceful system

shutdown. This button is recessed to prevent accidental server power off. Use the tip of a pen to

operate this button.

7.

Disconnect the power and cables from the server.

See 

“Disconnect Cables From the Server” on page 80

.

Related Information

■

“Power Down Server Gracefully Using the Power Button” on page 77

■

“Power Down Server For an Emergency” on page 79

■

“Disconnect Cables From the Server” on page 80

■

“Power On the Server” on page 214

Power Down Server Gracefully Using the Power Button

Note - 

You can use the Power button on the front of the server to initiate a graceful system shut

down. This button is recessed to prevent accidental server power off.

1.

Use a pen or other pointed object to press and release the power button on the

front panel.

Preparing for Service

77

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands