manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 81

Take Antistatic Measures

Related Information

■

“Disconnect Cables From the Server” on page 80

■

“Take Antistatic Measures” on page 81

■

“Reinstall the Server Chassis in the Rack” on page 213

Take Antistatic Measures

1.

Prepare an antistatic surface on which to set parts during removal and

installation.

Place ESD-sensitive components such as the printed circuit boards on an antistatic mat. The

following items can be used as an antistatic mat:

■

Antistatic bag used to wrap a replacement part

■

An ESD mat, orderable from Oracle

■

Disposable ESD mat (shipped with some replacement parts or optional system components)

2.

Attach an antistatic wrist strap.

When servicing or removing server components, attach an antistatic strap to your wrist and then

to a metal area on the chassis. Then disconnect the power cords from the server.

Related Information

■

“Remove the Server From the Rack” on page 80

■

“Remove the Top Cover” on page 81

■

“Remove Antistatic Measures” on page 212

Remove the Top Cover

All field-replaceable units that are not accessed from the front or rear of the system require the

removal of the top cover.

Preparing for Service

81

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands