Oracle Sun Netra X4270 Service Manual Download Page 213

Page: 213 / 238

Reinstall the Server Chassis in the Rack

Related Information

■

“Take Antistatic Measures” on page 81

■

“Install the Top Cover” on page 211

■

“Reinstall the Server Chassis in the Rack” on page 213

Reinstall the Server Chassis in the Rack

After servicing the system, reinstall it back into the rack.

Caution -

The server weighs approximately 41 lbs (18.6 kg). Two people are required to carry

the chassis and install it in the rack.

Lift the server from the antistatic mat and reinstall the server into the rack.

Refer to the

Sun Netra X4270 Server Installation Guide

for the installation instructions specific

to your rackmount kit.

Related Information

■

“Remove the Server From the Rack” on page 80

■

“Remove Antistatic Measures” on page 212

■

“Reconnect Power and Data Cables” on page 213

Reconnect Power and Data Cables

Reconnect the data cables to the rear of the server, as appropriate.

Reconnect the power cables to the power supplies.

If necessary, reinstall the appropriate cables in to a cable management device.

Power on the server.

See

“Power On the Server” on page 214

Related Information

■

“Disconnect Cables From the Server” on page 80

■

“Reinstall the Server Chassis in the Rack” on page 213

■

“Power On the Server” on page 214

Returning Server to Operation

213

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands