Oracle Sun Netra X4270 Service Manual Download Page 79

Page: 79 / 238

Power Down Server For an Emergency

Power Down Server For an Emergency

Caution -

This task quickly forces the server???s main power off. You might corrupt your

system data during an emergency power down, so only use this task to power down the server

after attempting the graceful power down tasks.

Press and hold the power button for four seconds to force the main power off

and to enter standby power mode.

When main power is off, the power OK LED on the front panel will begin flashing, indicating

that the server is in standby power mode. See

“System Status LEDs” on page 19

Disconnect the power and data cables from the server.

See

“Disconnect Cables From the Server” on page 80

Caution -

When you use the Power button to enter standby power mode, power is still directed

to the service processor remote management subsystem and power supply fans. To completely

power off the server, you must disconnect the AC or DC power cords from the back of the

power supplies.

Related Information

■

“System Status LEDs” on page 19

■

“Power Down Server Gracefully” on page 76

Preparing for Service

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands