Oracle Sun Netra X4270 Service Manual Download Page 17

Page: 17 / 238

Locating Controls and Connectors

Rear Panel Cable Connections

No.

Description

Additional Information

SAS port

SAS SFF-8088 connector

Alarm port

Telco alarm port

PCIe2 slot 0

X8 PCIe2 low-profile

PCIe2 slot 4

X8 PCIe2 full-height, full-width

PCIe2 slot 1

X8 PCIe2 low-profile

PCIe2 slot 5

X8 PCIe2 full-height, full-width

PCIe2 slot 2

X8 PCIe2 low-profile

Power Supply 0

Labeled PS0

Power Supply 1

Labeled PS1

SER MGT port

SP serial management port

NET MGT port

SP network management port

Gigabit Ethernet ports

Left to right – NET0, NET1, NET2, NET3

Grounding wire studs

System ships with a grounding lug

USB ports

Left to right – USB0, USB1

Video port

VGA port

Understanding the Server

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands