Oracle Sun Netra X4270 Service Manual Download Page 215

Page: 215 / 238

Identifying the Server Ports

These topics describe the pinouts of the server connectors.

■

“Gigabit Ethernet Ports” on page 215

■

“Network Management Port” on page 216

■

“Serial Management Port” on page 217

■

“Video Connector” on page 219

■

“Alarm Port” on page 220

■

“USB Ports” on page 221

■

“External SAS Connector” on page 222

■

“PCI Mezzanine Auxiliary Power Connector” on page 223

Related Information

■

“Understanding the Server” on page 13

Gigabit Ethernet Ports

The server has four autonegotiating 10/100/1000BASE-T Gigabit Ethernet system domain

ports. All four Ethernet ports use a standard RJ-45 connector. The transfer rates are shown in

the following table.

Connection Type

IEEE Terminology

Transfer Rate

Ethernet

10BASE-T

10 Mbps

Fast Ethernet

100BASE-TX

100 Mbps

Gigabit Ethernet

1000BASE-T

1000 Mbps

The following figure and table describe the gigabit Ethernet port pin signals.

Identifying the Server Ports

215

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands