manualshive.com logo in svg

Omron XPECTIA FZ3, User Manual

Share
Download
Omron XPECTIA FZ3 User Manual Download Page 306

3

Compensate 

image

304

Color Gray Filter

FZ3 Processing Items List Manual

Setting item

Set value

[Factory default]

Description

RGB Filter

●

[Red filter]

●

Green filter

●

Blue filter

●

Cyan filter

●

Magenta filter

●

Yellow filter

●

Brightness filter(R+G+B)

●

Brightness filter(R+2G+B)

●

Custom filter

●

Minimum filter

This item produces the same effects as using
the selected optical filters.

Gain (Red)

0.0001 to 9.9999
[0.3]

RGB gain values when processing with a
custom filter.The density of the color
component increases as the value increases.
This can be set only when "Custom filter" is
selected for RGB filter.

Gain
(Green)

0.0001 to 9.9999
[0.59]

Gain (Blue)

0.0001 to 9.9999
[0.11]

When you choose the HSV option

5.

Select the type of filter in the "HSV filter" area.

Setting item

Set value

[Factory

default]

Description

HSV filter

●

Fast

●

[Fine]

"Fast": The color extraction range is set only by hue.
"Fine": Extraction is set by standard hue, hue range, and color
chroma.

Standard
Hue

[0] to 359

Specify the standard hue (tone) for the HSV filter.The density
decreases as the difference in hue from the standard hue (difference
in tone) increases.

Hue range

10 to 180
[90]

Specify the hue range (difference in tone) of the HSV filter.The hue
difference is obtained by dividing the specified hue range into 255
subranges with the standard hue as the center subrange. The density
of the hue outside the hue range is 0. This can only be set when
"Fine" is selected.

Acesst 1.0 6251194

Summary of Contents for XPECTIA FZ3

























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands