manualshive.com logo in svg

Omron XPECTIA FZ3, User Manual

Share
Download
Omron XPECTIA FZ3 User Manual Download Page 194

2

Measurement

192

L

FZ3 Processing Items List Manual

Output
parameter

This item can be changed if necessary.Normally, the factory default value may be used.
Use the output parameter to specify how to handle the coordinates.
Reference:

Output Parameters (L) (p.205)

Color Specification (L)

When connecting a color camera, specify the color to be measured.There are two specification methods:
specifying the color to be extracted in the image or specifying the color with the hue, saturation, and
brightness values.
This section describes how to specify colors in an image and gives an example of the procedure for
finely adjusting with numeric input afterwards.

1.

In the Item Tab area, tap [Color].

2.

Place a check at [Auto setting].

3.

In the Image Display area, specify the color range you want to detect by dragging the cursor from

the upper left corner to the lower right corner of that area.
The color of the specified area is automatically set.

4.

Finely adjust the hue, saturation, and brightness if necessary.

Adjust either by adjusting on the color chart or by inputting numbers.

Item

Set value

[Factory default]

Description

H

0 to 359

Specify the color phase (difference of color hues).

S

0 to 255

Specify color saturation (difference of color saturation).

V

0 to 255

Specify the brightness (difference of brightness).

Auto setting

●

Checked

●

[Unchecked]

Specifying the color to be measured on the image automatically
sets the hue, saturation, and brightness.

Color inv.

●

Checked

●

[Unchecked]

Everything other than the specified color becomes the
measurement target.

About color charts

Acesst 1.0 6251194

Summary of Contents for XPECTIA FZ3

























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands