manualshive.com logo in svg

Omron XPECTIA FZ3, User Manual

Share
Download
Omron XPECTIA FZ3 User Manual Download Page 235

2

Measurement

FZ3 Processing Items List Manual

Fine Matching

233

4.

Set up the judgement condition.

Setting item

Set value

Description

Quantity

0 to 9999

Specify the range of the number of labels that is judged to be OK..
When "Binary area" is used, the white pixels as a whole will be
regarded as one label.

Area

0 to
999999999.9999

Specify the range of the area that is judged to be OK..
When the "Labeling" is used, the area of the label number will be
specified instead.

Defect pos X

-99999.9999
to
99999.9999

Specify the X and Y axis move ranges for the center of gravity
positions that are judged to be OK.
When the "Labeling" is used, the center of gravity position of the label
number will be specified instead.

Defect pos Y

-99999.9999
to
99999.9999

Specify the X and Y axis move ranges for the center of gravity
positions that are judged to be OK.
When the "Labeling" is used, the center of gravity position of the label
number will be specified instead.

Note

●

Defect coordinates give the center of gravity position of detected defects.

Output Parameters (Fine Matching)

Specify how to treat the coordinates to be output to the external device as measurement results.This
item can be changed if necessary.Normally, the factory default value will be used.

Important

●

After setting up the measurement parameters, changing the output parameters will cause measurement results

to vary accordingly.If the output parameters have been changed, re-specify the measurement, too.

1.

Tap [Output parameter] in the Item Tab area.

Acesst 1.0 6251194

Summary of Contents for XPECTIA FZ3

























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands