Olympus OEP-3, Service Manual

Page: 12 / 176

1-6
OEP-3 V1 (UC)
10
Introduction
Location and Function of Parts and Controls (Continued)
on the PRINTER SETUP menu changes linked with this button setting. You can change the number even when the printer is printing.
5
RIBBON REMAIN button (25, 74 )
Press this button to display the type and the
number of printouts that can still be made on the regular screen. To not display them, press this button again. The setting of RBN REMAIN on the OUTPUT SETUP menu changes linked with this button setting.
6
INPUT SELECT button (19)
Press this button to select the input signal on
the regular screen. When you press this button, the currently selected input signal is displayed for about three seconds. To select the input signal, release the button while the desired input signal is displayed. Each time you press this button, the input signal is switched in the order of VIDEO, RGB, S-VIDEO, RGB...
7
MEMORY FRM/FLD button (23, 38)
Press this button to select the memory mode
on the regular screen. When you press this button, the currently selected memory mode is displayed for about three seconds. To select the memory mode, release the button while the desired memory mode is displayed. Each time you press this button, the memory mode is switched in the order of FRAME, FIELD, FRAME.
To make a printout of a captured image which
is blurred, set the memory mode to FIELD and eliminate the blur by pressing this button, and then make a printout.
8
MOTION CHECK button (51, 52)
Press this button to select the mode on the
regular screen to check whether the memory images are blurred when you captured two- or four-reduced images. Each time you press this button, the type is switched in the order of ON, OFF, ON...
The setting of MOTION CHK on the
PRINTER SETUP menu changes linked with this button setting.
9
CAPTION INPUT button (61)
Press this button to display or clear the
CAPTION menu on the regular screen.
0
CAPTION ON/OFF button (68) Used to determine whether a caption is printed on the printout. To make a printout with a caption, press this button to display ON. To make a printout without a caption, press this button to display OFF.
qa
CLEAR button (71, 72) Press this button to clear the images captured in the memory pages. Which images can be cleared with the CLEAR button depends on the setting made with the FUNCTION SETUP menu. When the clear function of this button is set to OFF, the buzzer sounds if you press the CLEAR button.
qs
EXEC button (62, 98, 104, 108, 124, 125, 126) Press this button to execute the values set with the COLOR ADJUST menu or to recall a user set in the PRINTER SETUP menu and to register the user set in the SYSTEM SETUP menu. Also, this button is used to enter the characters of a caption in the CAPTION menu.
qd
Cursor keys Use to select a desired item from the menu. Also, these keys are used to position the cursor (green pointer ) on the regular screen when capturing mulitple reduced images.
qf
INPUT SETUP button (21, 86) Press this button to display the INPUT SETUP menu on the regular screen.
qg
DISPLAY button (25, 73, 107) When the regular screen is displayed, pressing this button toggles the screen display on and off of (messages such as, Q1, A, etc.) regardless of the setting of the DISPLAY item in the OUTPUT SETUP menu. The setting of DISPLAY in the OUTPUT SETUP menu changes linked with this button. When the menu is displayed, pressing this button temporarily clears the menu display. While this button is held down, the menu display disappears.
11
Introduction
qh
R/G/B/D/L button (93) Press this button to display or clear the COLOR ADJUST menu on the regular screen.
qj
LOAD COLOR button (94) Press this button to recall the values set for the printout color (color intensity and color contrast). Pressing this button causes the
currently selected LOAD COLOR number to be displayed for about three seconds. Three kinds of LOAD COLOR numbers are available for the currently selected user set. To select the desired LOAD COLOR number, release the button while the desired LOAD COLOR number is displayed.
The selected LOAD COLOR number in the
COLOR ADJUST menu changes linked with this button.
Rear
1
t
INPUT (input signal) connectors (80)
Used to connect the video equipment supplying the source image.
Connectable equipment Video equipment with Y/C separated output connector Video equipment with composite video signal output connector Video equipment with RGB/SYNC output connectors
Connector S-VIDEO VIDEO RGB SYNC
2
75
Ω
ON/OFF termination switch (80)
Provided for the RGB input. Normally set this switch to ON. Set it to OFF if the input signal should drop when you connect additional equipment to the video equipment.
3
75
Ω
ON/OFF termination switch (80)
Provided for the NTSC composite video signal
in NTSC mode and PAL composite video signal in PAL mode.
Normally set this switch to ON. Set it to OFF
if the input signal should drop when you connect additional equipment to the video equipment.
4
Equipotential ground terminal connector
Used to connect to the equipotential plug to
bring the various parts of a system to the same potential.
Refer to
“Important safeguards/notices for use
in the medical environments
”on page 2.
Continue to the next page
c