Olympus OEP-3, Service Manual

Page: 62 / 176

1-56
OEP-3 V1 (UC)
110
Installation and Adjustment
Setting Up the Printer (Continued)
40&40
50&40
60&40
40&50
50&50
60&50
40&60
50&60
60&60
COLOR BALANCE
BAL X
: 5
0
[
1
–
50
–
99]
BAL Y
: 5
0
[
1
–
50
–
99]
BAL
STEP
: 10 [1
–
20]
TEST PRINT
: PRESS [EXEC]
PRN SETUP
: PRESS [ > ]
Q1 A 1
S
COLOR : 200
To perform rough adjustment To perform color balance adjustment beyond the current color balance range, increase the value of the BAL STEP.
2
Make a test print by repeating steps 5, 6, 7 and 8 in
“Adjusting the Color
Balance
” on page 107.
3
Select the image with the best color balance among the 9 images, if you can decide. Then display the values of BAL X and BAL Y by using the
F
,
f
,
G
or
g
button.
Repeat steps 1 and 2 until you have obtained the best color balance.
4
Go back to step 10 in
“Adjusting the Color Balance
” on page 109.
If you change BAL STEP from 05 to 10, the color balances of the test print are changed as illustrated.
111
Installation and Adjustment
P
R
N
S
P
E
E
D
: /
HIGH
MOTION CHK
P
/c
/
l
/
P
R
N
/
i
/
o
/
RI
N
T
E
R
S
E
T
U
P
PRINTER SETUP
COLOR : 200
/ COL / LAY / PRN / IN / OUT / PRINT QTY.
: 1 [ 1 ~ 9 ]
INTERVAL
: OFF / ON
GAMMA
: S / NORMAL / H : OFF / ON
LOAD USER
: 1 / 2 / 3 [ EXEC ]
SYSTEM
: PRESS [ > ]
FUNCTION
: PRESS [ > ]
C - BALANCE
: PRESS [ > ]
Q1 A 1
S
Selecting the Operation Mode f
or A
utomatic Printing
Capabilities
You can control the printer using either of the following remote control units connected to the REMOTE 2 or REMOTE 3 connector on the rear panel of the printer. •
RM-91 Remote control unit (provided by Sony Corporation): Connected to the REMOTE 2 connector
•
FS-30 Foot switch (provided by Sony Corporation): Connected to the REMOTE 3 connector. In addition, you can also remote control the printer by using a remote control unit which sends the remote control signal to the Pin No.5 of the REMOTE 3 connector.
Using the menu, you can assign the desired functions to the remote control unit connected to the REMOTE 2 or REMOTE 3 connector. In addition, the printer can be remotely controlled by a pulse signal input to REMOTE 2 or REMOTE 3. (See pages 131 and 132). Also, you can control the printer using a personal computer. For detailed information on controlling with the computer, contact your Olympus representative or the nearest Olympus service center.
Note
The FS-36 foot switch (provided by Sony Corporation) is connected to REMOTE 2 to control the printer. However, the function of this foot switch cannot be assigned using the menu.
1
Press the MENU button, then select PRN by pressing the
G
or
g
button.
The PRINTER SETUP menu appears on the source image.
1,7
2,4,6
3
5,6
Switch PRN to green by pressing the
G
or
g
button.
Display PRN in capital letters by pressing the
G
or
g
button.
Continue to the next page
c