Olympus OEP-3, Service Manual

Page: 72 / 176

1-66
OEP-3 V1 (UC)
130
Others
Specifications
Power requirements
100 to 120 V AC, 50/60 Hz
Power consumption
About 2.8 A max. at 25
°C, 120 V
AC
Operating temperature
5
°C to 35
°C (41
°F to 95
°F)
Operating humidity
20 % to 80 % (no condensation
allowed)
Storage and transport temperature
–
20
°C to 60
°C (
–
4
°F to 140
°F)
Storage and transport humidity
20 % to 90 % (no condensation
allowed)
Dimensions
About 370
×
125
×
490 mm
(w/h/d) (14
5
⁄
8
×
5
×
19
3
⁄
8
inches)
Mass
About 14.5 kg (31 lb 15 oz)
Printing system
Sublimation heat transfer printing
Thermal head
11.6 dot/mm (2048 dots)
Total gradation
256 levels each for yellow,
magenta, and cyan
Printing time
A
pproximately 20 seconds (at
color printing at high speed)
TV system
Selectable with the NTSC/PAL selector In NTSC mode: NTSC/EIA
standards
In PAL mode: PAL B.G.I
standards
Input connectors
RGB SYNC (analog RGB signal):
BNC connector
×
4
RGB: 0.7 Vp-p (75 ohm termination switch set to ON) SYNC: 0.3 to 4 Vp-p SYNC ON G: Automatic discrimination 75 ohms (75 ohm termination switch set to ON), sync negative
S VIDEO (Separate luminance (Y)
and chrominance (C) signals): 4-pin mini-DIN
×
1
Y: 1 Vp-p C: For NTSC/EIA standards: 0.29 Vp-p color burst For PAL B.G.I standards: 0.3 Vp-p color burst 75 ohms (terminated), sync negative
VIDEO (NTSC composite video
signal for NTSC/EIA standards and PAL composite video signal for PAL B.G.I standards): BNC connector
×
1
1 Vp-p, 75 ohms (75 ohm termination switch set to ON), sync negative
AC IN (for power input)
Output connectors
RGB SYNC (analog RGB signal):
BNC connector
×
4
RGB: 0.7 Vp-p (75 ohm termination switch set to ON) SYNC: 1 Vp-p 75 ohms (terminated), sync negative
S VIDEO (Separate luminance (Y)
and chrominance (C) signals): 4-pin mini-DIN
×
1
Y: 1 Vp-p C: For NTSC/EIA standards: 0.29 Vp-p color burst For PAL B.G.I standards: 0.3 Vp-p color burst 75 ohms (75 ohm termination switch set to ON), sync negative
VIDEO (NTSC composite video
signal for NTSC/EIA standards and PAL composite video signal for PAL B.G.I standards) BNC connector
×
1
1 Vp-p, 75 ohms (terminated), sync negative
131
Others
BUSY
MIN
GND
FL2
FL1
CN5
1 3
2
Controls connectors
REMOTE 1 : special mini jack
×
1
For MAJ-898 Remote Control Unit (supplied)
REMOTE 2 (automatic printing
connector): Stereo mini jack :
×
1
For RM-91 Remote Control Unit (provided by Sony Corporation) and FS-36 Foot Switch (provided by Sony Corporation)
REMOTE 3 (automatic printing
connector): D-SUB 9-pin connector:
×
1
For FS-30 Foot Switch (provided by Sony Corporation) (See
“Selecting the Operation
Mode for Automatic Printing Capabilities
” page 111)
RS-232C (Computer control
interface): D-SUB 25-pin connector
×
1
Output: 5 kilohms at load Typical ± 8 V Input: 5-kilohm load High level 5 to 15 V Low level
–
5 to
–
15 V
Supplied accessories
Color printing pack (1) Ink ribbon holder (1) Paper tray (1) Paper cover (1) MAJ-868 remote control unit (1) Connecting cable for remote
control unit (1)
R6 (size AA) 1.5 V battery (1) AC power cord (1) Warranty card (1) Instructions for Use (1)
Optional accessories
UPC-510 Color Printing Pack
(provided by Sony Corporation)
UPC-540 Self-laminating Color
Printing Pack (provided by Sony Corporation)
Medical Specifications
Protection against electric shock:
Class I
Protection against harmful ingress
of water: Ordinary
Degree of safety in the presence of
flammable anesthetics or oxygen: Not suitable for use in the presence of flammable anesthetics or oxygen
Mode of operation:
Continuous
Using the automatic printing capabilities (REMOTE 2/REMOTE 3)
If you send remote control pulse signals illustrated through the REMOTE 2 or REMOTE 3 connector, the printer is remotely controlled according to the remote control setting. (See page 111.) Turn on the power of the printer and display the source image on the monitor screen. Send a remote control pulse signal at the timing shown below. The timing depends on the setting on item IMMED. CAP of the FUNCTION SETUP menu.
Note
The remote control pulse signal examples introduced here are one example of typical operation timing. The timing may be affected due to the memory page selected and print type. CAPTURE timing pulse for REMOTE 2 REMOTE 2 connector pin assignment: