manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 97 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 97

Configuring Your Workstation    4-25

System Management

The following screen appears if you select [System Management] on the [System Hardware] menu
and press 

Enter

.

Available options in this menu are listed below.

Option

Parameter

Description

Your Setting

BIOS Revision

–

Displays the current BIOS version.
(View only)

Board Part
Number

–

Displays the mother board part
number. (View only)

Board Serial
Number

–

Displays the mother board serial
number. (View only)

System Part
Number

–

Displays the system part number.
(View only)

System Serial
Number

–

Displays the system serial number.
(View only)

Chassis Part
Number

–

Displays the chassis part number.
(View only)

Chassis Serial
Number

–

Displays the chassis serial number.
(View only)

Onboard LAN1
MAC Address

–

Displays the MAC address of onboard
LAN controller. (View only)

[   ]: Factory-set

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments