manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 138 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 138

5-18    Installing the Operating System with Express Setup

 

18. 

Copy optional Mass Storage Driver module.

If you install optional Mass Storage Driver, the message will be shown.

Insert CD-ROM or floppy disk attached to the Mass Storage Driver and proceed operation
according to the message.

 

19. 

Remove NEC EXPRESSBUILDER DVD from the optical disk drive according to the
message.

If you proceed the setup by using setup parameter file, remove the floppy disk from the
floppy disk drive.

 

20. 

Insert Windows 7 DVD-ROM into the optical disk drive.

NOTE:

 Windows 7 and selected applications will be installed

automatically and reboots several times.

 

21. 

[Agree Software License Agreement] screen appears.

Read the license terms carefully. If you agree, select I accept the license terms, and then
click [Next].

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments