manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 183 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 183

Maintenance  7-5

Cleaning the Keyboard/Mouse

Make sure that the workstation and peripheral devices are all off-powered (the POWER/SLEEP
lamp goes off), and then wipe the keyboard surface with a dry cloth.

The mouse operation depends on the degree of smoothness of the internal ball rotation. To keep the
mouse ball clean, use the mouse in a place with little dust. Follow the steps below to clean the
mouse regularly:

 

1. 

Make sure that the workstation is off-powered (the POWER/SLEEP lamp goes off).

 

2. 

Turn the mouse upside down, and rotate the mouse ball cover counterclockwise to remove
it. Take out the ball from the mouse.

Mouse ball cover

Mouse ball

Roller

Bottom View

 

3. 

Wipe the mouse ball with a dry soft cloth.

Or, soak a soft cloth in neutral detergent that is diluted with cold or lukewarm water, and
squeeze it firmly. Rub off stains on the mouse ball.

 

4. 

Wipe three small rollers inside the mouse with a cotton swab soaked with alcohol.

 

5. 

Put the mouse ball back into the mouse.

 

6. 

Place the mouse ball cover, and rotate it clockwise until it is locked.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments