manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 91 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 91

Configuring Your Workstation    4-19

Advanced Chipset Control

The following screen appears if you select [Advanced Chipset Control] on the Advanced menu.

Available options in this menu are listed below.

Option

Parameter

Description

Your Setting

Multimedia Timer

[Enabled]
Disabled

Enables or disables high-precision
event timer.

Intel(R) VT-d

[Enabled]
Disabled

Enables or disables the Intel(R)
Virtualization Technology for Directed
I/O feature.
This menu appears only when the
processor supports this feature.

Wake On
LAN/PME

[Enabled]
Disabled

Enables or disables the remote
power-on feature through network or
by the PME signal sent from PCI
device.

Wake On Ring

[Disabled]
Enabled

Enables or disables the remote
power-on feature through the serial
port.

[   ]: Factory-set

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments