manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 265 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 265

Installing Windows 7    D-7

INSTALLING Windows 7

Preparations for Installation

„

 

NEC EXPRESSBUILDER DVD

„

 

Microsoft OS Installation media (hereinafter referred to as "Windows 7 DVD-ROM")

„

 

User's Guide

„

 

Getting Started

„

 

Windows 7 OEM-Disk for EXPRESSBUILDER

Creating "Windows 7 OEM-Disk for EXPRESSBUILDER"

Before installing, create Windows 7 OEM-disk for EXPRESSBUILDER.

NOTE:

 If you have already "Windows 7 OEM-Disk for

EXPRESSBUILDER" for NEC Express5800 Workstation which you
are going to install Windows 7, you do not need to create it again.

NOTE:

 What is "OEM-Disk"?

„

 

In case of creating the disk for Windows 7 Professional 64-bit (x64)
Edition:
It is called [Windows 7 x64 Edition OEM-Disk for
EXPRESSBUILDER].

„

 

In case of creating the disk for Windows 7 Professional 32-bit (x86)
Edition:
It is called [Windows 7 OEM-Disk for EXPRESSBUILDER].

You can create Windows 7 OEM-Disk for EXPRESSBUILDER with the following two procedures.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments