Home
/
NEC
/
Express5800/53La
/
User Manual

NEC Express5800/53La, User Manual, Page: 301 / 314

Share

286 pages before
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314

Page: 301 / 314

NEC Express5800/53La User Manual Download Page 301

Installing Windows XP E-13

9.

Remove the NEC EXPRESSBUILDER DVD from the optical disk drive, restart the
system.

Please perform setting of Link Speed and WOL mentioning in "LAN Driver Setting"
(Page E-14).

NOTES:

To change the LAN driver and PROSet settings, log on to the
system from a local console using an administrator account.
Remotely changing the settings by using the operating system’s
remote desktop feature is not supported.

[Internet Protocol (TCP/IP)] check-box must be checked to set an IP
addresses. According to the circumstances, the check-box may not
be checked at the beginning. Manually check the check box and set
an IP addresses.

«
...
299
300
301
302
303
...
»

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments