manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 66 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 66

3-10  Setting Up Your Workstation

CONNECTING PERIPHERAL DEVICES

Connect peripheral devices to the workstation. The workstation is provided with connectors for
wide variety of peripheral devices. The figure on the next page illustrates available peripheral
devices for the workstation in the standard configuration and locations of the connectors for the
devices.

WARNING

Observe the following instructions to use the workstation safely. Failure to
follow these instructions may result in death or serious personal injury. See
pages 1-3 to 1-10 for details.

■

 

Do not hold the power plug when your hands are wet.

■

 

Do not connect the ground line to a gas tube.

CAUTION

Observe the following instructions to use the workstation safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-10 for details.

■

 

Plug into a proper power source.

■

 

Do not connect the power cord to an outlet that has an illegal number of
connections.

■

 

Do not use the workstation with any loose interface connection.

■

 

Use the authorized power cord only.

■

 

Do not connect the grounding line to water tube.

■

 

Do not connect the grounding line to the ground terminal for telephone line.

■

 

Do not connect any interface cable with the power cord of the workstation
being connected to a power source.

■

 

Do not use any unauthorized interface cable.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments