manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 72 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 72

3-16  Setting Up Your Workstation

MAKING BACKUP COPIES OF SYSTEM INFORMATION

The system information includes the current BIOS settings and any specific information for the
workstation.

Save the information after completing the system setup.

Without the backup data, you will not be able to recover the information.

You can save the information by the following process.

 

1. 

Connect Flash FDD or USB FDD to the USB connector.

 

2. 

Insert the NEC EXPRESSBUILDER DVD into the optical disk drive and reboot the
system.

 

3. 

Select [Tool menu].

 

4. 

Select [English].

 

5. 

Select [Maintenance Utility].

 

6. 

Select [System Information Management].

 

7. 

Select [Save].

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments