manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 303 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 303

Installing Windows XP    E-15

WOL

Refer to the following procedure for WOL (Wake On LAN) setting.

IMPORTANT: 

WOL supports only Standard network adapter.

When PROSet is installed

 

1. 

Start Device Manager.

 

2. 

Point to [Network adapters] and double-click following adapter.

Open the adapter [Properties].

[Intel(R) 82578DM Gigabit Network Connection]

 

3. 

Click [Power Management] tab and change setting in [Wake On LAN] according to the
following list.

Setting item

Using WOL

Not using WOL

"Wake On Directed Packet"

ON or OFF

OFF

"Wake On Magic Packet"

ON

OFF

"Wake on Magic Packet from power off state"

ON

OFF

"Wake on Link"

OFF

OFF

NOTES:

„

 

Please refer to follows about function of "Wake On Directed
Packet".

ON: WOL work by DirectedPacket on hibernate or standby state.

OFF: WOL do not work by DirectedPacket on hibernate or standby

state.

„

 

Above setting will be maintained until manually resetting are
executed.

*1 The packet which includes ethernet address of adapter in Ethernet

Header or the Packet including the IP address assigned by IP Header
to adapter.

 

4. 

Click [OK].

 

5. 

Restart the system.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments