Home
/
NEC
/
Express5800/53La
/
User Manual

NEC Express5800/53La, User Manual, Page: 164 / 314

Share

Page: 164 / 314

NEC Express5800/53La User Manual Download Page 164

6-6 Installing and Using Utilities

Parameter File Creator

"Parameter File Creator" is a tool to create [Parameter file] that is used for configuring the
workstation with the Express Setup (see Chapter 5 for details).

If you use the Parameter file created by the Express Setup and Parameter File Creator to operate the
setup, you can setup from the installation of OS to several utilities automatically except for a few
key input to confirm the specification. Also, you can install the system with the same specification
as before when re-installing the system. We recommend you to create [Parameter file] to setup the
workstation from NEC EXPRESSBUILDER.

When using a floppy disk, a USB floppy disk drive is required.

IMPORTANT:

You can not create [Parameter file] for Microsoft Windows 7 x64
Edition.

The setup using a parameter file saved in the Flash FDD is not
supported.

NOTE:

You can install Windows 7 without [Parameter file].

Also, you can modify/newly create [Parameter file] during the setup
with NEC EXPRESSBUILDER.

«
...
162
163
164
165
166
...
»

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments